valve 생산에 쓰이는 노동력과 장비를 바탕으로 pump와 flow controller도 함께 생산하기 시작했다.
i. Valve의 생산라인은 네 개의 부품 조립으로 구성된다. 다른 회사들도 이제 Wilkerson사와 비슷한 품질의 valve를 만들 수 있지만 아직까지는 값 싸고 질 좋은 valve로 시장점유율을 위협하는 경쟁사들은 없다. 그
control로는 안전장치를 대신할
수 없음
Safety valve
밸브전단의 Static Pressure가 어느 압력을 넘을 경우 자동적으로 작동되어 과압을 방출하는 밸브이다.
밸브가 신속하게 완전히 열리며 보통 압축성 유체에 사용된다.
flare system: 안전밸브 등에서 배출되는 물질을 모아 flare stack에서 소각
(1차분진 층)을 형성하여 입자상 물질을 분리 포집
여과집진기의 집진원리
격막밸브(Diaphragm Valve)
격막밸브: 솔레노이드밸브(SolenoidValve)의 순간
작동으로 격막밸브가 압축공기를 분사시켜 콤프레서에서
공급된 고압 공기를 Blow Tube에 순간적으로 많은 양의
압축 공기를 불어넣어 주는 역할
1
2
ControlValve : Needly SUS Valve
2.4 Water Bath
(1) Temperature Control : TIC Digital display
(2) Sensor : RTD Pt 100Ω
(3) Heating System : Cartridge pipe heater
(SUS) 220V x 500W 2ea
(4) Heating Bath : SUS 25 x 25 x 15 cm
(5) Visual Bath : Pyrex Glass φ170 x 390 x 8t
(6) Reactor tube : φ5mm x L 18.5m
(7) Agitator : Geard motor type RPM 150
2.5 Feed Pump
(1) A Solution :
ranges, the thermal conductivity can usually be approximated by
(a, b is empirical constants)
4) Close valve#8 and give the pressure by blocking ‘vinyl’ pipe by using valve V4, V5, V9.
Remove the air in pipe by open and close valve V4, V5, V9.
Then, controlvalve #3 V3 to flow more than 100L/hr.
- If water doesn’t flow at all, follow these operations again and again.
Evaluate the pressure drop driven by each pipe accessories such as
Gate valve, Standard Elbow Bend,
90˚ Mitre Bend, Straight pipe, Glove Valve and Sudden Enlargement.
Q = V1A1 = V2A2
The Law of Conservation of Mass states that mass can be neither created nor destroyed.
Using the Mass Conservation Law on a steady flow process through a control volume where the stored mass in the control
valve (if there is damage)
< Operation > (usually combined with on-going medical management )
Bentall procedure - Replacement of the damaged section of aorta and replacement of the aortic valve.
David procedure - Replacement of the damaged section of aorta and reimplantation of the aortic valve.
Insertion of a stent graft, ex) TEVAR(thoracic endovascular aortic repair).
Follow up
관한 식으로 바꾼다.
즉,
Bypass valve와 controlvalve를 통하여 유량조절을 하면서 수두 차를 확인한다
이 때 메스실린더와 초시계를 이용하여 유량을 측정한 후 data를 기록한다.
모든 실험을 마친 후 동파 방지를 위하여 장치의 모든 valve를 열어 물을 배수하고, tank안의 물도 완전히 빼준다.
증류이론 및 Pilot Plant를 운전, 해석에 그 목적을 둔다.
2. 실험 과정
1) 냉각수를 E-100(Double Pipe Exchanger), E-101(Condensor)로 공급한다.
2) Control Box를 가동 후, Power Switch ON.
3) T-100(Feed Tank)에 원료가 충분한지 확인 후, Tank Block Valve Open.
4) Column Feed Valve Open → 5단, 4단, 3단 순서로 열어준다. (실험 3번)