1.Photolithography
리소그래피는 포토레지스트를 도포하는 공정으로 시작해 노광, 현상, 에칭, 포토레지스트 제거에 이르는 일련의 프로세스이다. 현상까지를 레지스트 처리공정으로 하며, 에칭 공정과 분리해서 생각할 수도 있다. 현재, 패턴 노광은 레티클이라 불리는 마스크 기판에 의해 축소 투영 전
1. 실험 제목
Cantilever Beam을 이용한 Energy Harvesting Modeling
2. 이론
1) Energy Harvesting
거대 용량의 전기를 발생시키기 위한 전통적인 수력 발전, 화력 발전, 풍력 발전, 조력 발전, 태양광/태양열 발전 기술보다도 음파, 초음파, 또는 주위에서 쉽게 발생할 수 있는 소음, 떨림, 구부러짐, 수축, 신장과
4. STRUCTURE DESIGN
4.1. Wing structure
Wing structure
The wing on the plane is a part that the highest load take. The large bending moments especially act on the point near the root of wing. Also, we should consider the number of spar, rib, position, skin thickness and taper ratio.
I Beam shape
4.2. I BeamBeam theory shows that the I-shaped section is a very efficient form f
the overall sensitivity. For that reason, this way of operation is more difficult to implement and, until recently, most of the cantilever biosensors were based on the static mode.
Cantilever detection Modes of detection
In the optical lever scheme, the cantilever free end movement is detected by measuring the reflected laser beam displacement into a position-sensitive photodetector (PSD).
I. 실 험 목 적
1. 스트레인 게이지의 사용 목적과 원리를 이해하고, 부착 방법을 숙지한다.
2. strain gage로 외팔보의 변형률을 측정하여 외팔보의 응력-변형률-처짐 해석을 수행하고, 이론치와의 오차 원인에 대해 토의한다.
3. 스트레인 게이지를 이용하여 물체의 여러 가지 물성을 측정하는 방법
1. 이 론
(1) Energy harvesting
"Energy harvesting-에너지 하베스팅“은 ”Power Harvesting" 또는 “Energy Scavenging"과 같은 뜻으로 사용되는 것으로, ”자연의 버려지는 에너지를 수확하여 저장하는 기술“을 의미하며, 무선센서네트워크의 소형 독립전원을 제작하는데 많이 연구되고 있다. 에너지 하베스팅에 관한
1.실험 목적
외팔보의 스프링 상수와 탄성계수를 측정한다. 그리고 변위와 전압사이의 관계식을 만들고 그 의미를 이해한다. Energy harvesting의 모델링을 직접하여 보면서 실제 모델과 실험값의 결과를 분석하고 그 의미를 생각하여 본다.
2.실험 이론
(1) Energy harvesting
Energy harvesting (Power harvesting, Energy
I. 서론
A. 연구목적 및 필요성
온난화, 열대야와 같은 이상기후와 쓰나미, 집중호우, 사막화와 같은 대재난은 현재 글로벌 이슈가 되어, 전세계인들의 삶을 위협하고 있다. 그리고 전세계의 에너지원인 마르지 않을 것만 같았던 원유도 값의 폭등으로 인해 한계상황에 도달해 있다. 이와 같은 상황에서
3D printing
3D printing or additive manufacturing (AM) refers to any of the various processes for printing a three-dimensional object. Primarily additive processes are used, in which successive layers of material are laid down under computer control. These objects can be of almost any shape or geometry, and are produced from a 3D model or other electronic data source.
Basic principles
If the
캔틸레버의 탐침은 시료표면에 적용되는 힘이나 AFM의 lateral resolution을 결정.
Silicon , silicon nitride로 만듦
길이 100-200㎛, 넓이 40㎛, 두께 0.3-2㎛
표면에 수직하게 야기되는 반발력
반발력은 1~10 nN
작은 힘에도 매우 민감하게 반응하여 0.01 nm 정도로 미세하게 움직이는 것까지 측정
미세한 표면형상