1. 서론 (Introduction)
BaTiO3는 강유전성을 띠는 산화물로 알려져 있다. 온도가 1460℃ 이하일 때에는 육방정 (hexagonal) 구조를 취하다가 1460℃ 이상일 때에는 perovskite 구조로 상전이가 발생하게 된다. 그림에서 보듯이 perovskite 구조 내에서 BaTiO3는 여러 가지 다른 동질 이상 (polymorphism)을 갖는다.
온도 120
1.증류
휘발성 차이를 이용(비점의 차이에 의해)하여 액체혼합물로부터 각 성분을 분리하는 조작을 증류라고 한다. 혼합물중의 두 성분이 모두 휘발성분인 점에서 한쪽성분이 휘발성인것과는 구분된다. 일반적으로 증기압이 큰 성분 즉 비점이 낮은 성분이 휘발하기 쉽다. 따라서 증류에서는 각 성분의
1. 서론
1.1. 흡착
흡착은 용액 내에 보다 고체의 표면에 흡착된 분자의 농도가 더 크다는 사실을 설명하는 용어이며, 흡착제를 사용하여 목적 성분을 분리하는 조작의 하나이다. 흡착에는 물리적 흡착과 화학적 흡착이 있다. 물리적 흡착은 van der Waals 힘의 작용으로 일어나는 가역 현상이나, 화학적
Ⅰ. 기능성 식품이란?
기능성 식품의 정의는「식품성분이 갖는 생체방어, 생체리듬의 조절, 질병의 방지와 회 복 등 생체조절기능을 생체에 대하여 충분히 발휘할 수 있도록 설계되고 가공된 식품」이다. 또한 기능성 식품의 범위를「식품으로서 통상 이용되는 소재나 성분으로 구성되며 동시에 통상
고상법을 이용하여 만든 Y2O3:Eu 분말의 특성
황경섭, 김동운, 이상준, 이수영, 임상영
신소재공학과 성균관대학교
Characteristics of Y2O3:Eu powder using Solid state reaction
Hwang Gyung Sub, Kim Dong Un, Lee Sang Jun, Lee Soo Yung, Im Sang Yung
Advanced Materials Science and Engineering, SungKyunKwan Univ.
Abstract : Eu는 희토류 금속으로 촉매,
10 minutes excitation with Xe light of 1000lux for 5 minutes.
(2)Time to decrease the afterglow to 0.32mcd/㎡ when excited with above condition.
(3)Time required for saturation with Xe light at 1000 lux.
(4)Time to drop the initial afterglow brightness by 20% after irradiation with300W high pressure mercury lamp.
(Accelerated light fastness test)
(5)In powder form
of ink, colors and stiffness of materials of 3D printer but it is not a big deal. Though this problems prevent 3D printers form mass-producing the stuffs, diversified small-quantity production is possible with present technology fortunately. The stiffness of materials is 80 percent of the stuffs that is widely spread, and the kinds of materials of ink is very various, plastic, powder, rubber, wax
초록(Abstract)
본 보고서는 Powder method를 이용한 주석(Sn) 시편의 제작 과정 중 Sintering 과정의 온도 변화에 따른 Properties의 변화를 알아보기 위한 일련의 실험에 관한 것이다. 우선, 주석분말에 압력을 가해 시편을 만들고 Sintering 전후의 밀도를 측정하여 비교했으며, 열처리 온도에 따른 경도를 측정해
Cu의 특성 변화를 알아보는 것 이다. 이에 따라 나머지 변수들인 소결 온도 및 압력은 일정하게 유지하였다. 실험변수인 소결 시간은 각각 0 시간, 2 시간, 10 시간으로 처리했으며 온도는 700도, 압력은 300MPa로 통일하였다.
2.실험과정
1) 제조
①. 분말 준비(Cu)
②. 성형(compaction)
③. 소결(sintering)